Aviation Training Consultants: 800-874-5346
0
You have 0 items in your cart
Aviation Training Consultants: 800-874-5346
0
You have 0 items in your cart

FAR/AIM: Subpart F— Remote Identification Design and Production

Subpart F— Remote Identification Design and Production


 

§ 89.501 Applicability.

(a) This subpart prescribes—

(1) Requirements for the design and production of unmanned aircraft with remote identification produced for operation in the airspace of the United States.

(2) Requirements for the design and production of remote identification broadcast modules.

(3) Procedural requirements for the submission, acceptance, and rescission of declarations of compliance.

(4) Rules governing persons submitting declarations of compliance for FAA acceptance under this part.

(b) Except as provided in paragraph (c) of this section, this subpart applies to the design and production of all unmanned aircraft operated in the airspace of the United States.

(c) Except for unmanned aircraft designed and produced to be standard remote identification unmanned aircraft, this subpart does not apply to the design or production of:

(1) Home-built unmanned aircraft.

(2) Unmanned aircraft of the United States Government.

(3) Unmanned aircraft that weigh 0.55 pounds or less on takeoff, including everything that is on board or otherwise attached to the aircraft.

(4) Unmanned aircraft designed or produced exclusively for the purpose of aeronautical research or to show compliance with regulations.

 

§ 89.505 Serial numbers.

No person may produce a standard remote identification unmanned aircraft under § 89.510 or § 89.515 or a remote identification broadcast module under § 89.520, unless the producer assigns to the unmanned aircraft or remote identification broadcast module a serial number that complies with ANSI/CTA-2063-A. ANSI/CTA-2063-A, Small Unmanned Aerial Systems Serial Numbers (September 2019) is incorporated by reference into this section with the approval of the Director of the Office of the Federal Register under 5 U.S.C. 552(a) and 1 CFR part 51. All approved material is available for inspection at the FAA's Office of Rulemaking (ARM-1), 800 Independence Avenue SW, Washington, DC 20590 (telephone 202-267-9677) and is available from Consumer Technology Association (CTA), 1919 South Eads Street, Arlington, VA 22202, CTA@CTA.tech, 703-907-7600 or at https://www.cta.tech. It is also available for inspection at the National Archives and Records Administration (NARA). For information on the availability of this material at NARA, email fedreg.legal@nara.gov, or go to www.archives.gov/federal-register/cfr/ibr-locations.html.

 

§ 89.510 Production requirements for unmanned aircraft produced under a design approval or production approval issued under part 21 of this chapter.

After September 16, 2022, no person may produce an unmanned aircraft for operation in the airspace of the United States under a design approval or production approval issued under part 21 of this chapter unless:

(a) All applicable requirements of part 21 of this chapter are met; and

(b) The unmanned aircraft is—

(1) Designed and produced to meet the minimum performance requirements for standard remote identification unmanned aircraft established in § 89.310 in accordance with an FAA-accepted means of compliance; or

(2) Equipped with Automatic Dependent Surveillance-Broadcast (ADS-B) Out equipment that meets the requirements of § 91.225 of this chapter.

 

§ 89.515 Production requirements for unmanned aircraft without design approval or production approval issued under part 21 of this chapter.

Except as provided in § 89.510, after September 16, 2022, no person may produce an unmanned aircraft for operation in the airspace of the United States unless—

(a) The unmanned aircraft is designed and produced to meet the minimum performance requirements for standard remote identification unmanned aircraft established in § 89.310 in accordance with an FAA-accepted means of compliance; and

(b) All of the following conditions are met:

(1) Inspection requirements for production of standard unmanned aircraft. A person responsible for the production of standard remote identification unmanned aircraft must, upon request, allow the Administrator to inspect the person's facilities, technical data, and any standard remote identification unmanned aircraft the person produces, and to witness any tests necessary to determine compliance with this subpart.

(2) Audit requirements. A person responsible for the production of standard remote identification unmanned aircraft must cause independent audits to be performed on a recurring basis, and additionally whenever the FAA provides notice of noncompliance or potential noncompliance, to demonstrate the unmanned aircraft listed under a declaration of compliance meet the requirements of this subpart. The person responsible for the production of standard remote identification unmanned aircraft must provide the results of all such audits to the FAA upon request.

(3) Product support and notification. A person responsible for the production of standard remote identification unmanned aircraft must maintain product support and notification procedures to notify the public and the FAA of any defect or condition that causes an unmanned aircraft to no longer meet the requirements of this subpart, within 15 calendar days of the date the person becomes aware of the defect or condition.

 

§ 89.520 Production requirements for remote identification broadcast modules.

After April 21, 2021, no person may produce remote identification broadcast modules unless:

(a) The remote identification broadcast module is designed and produced to meet the minimum performance requirements for remote identification broadcast modules established in § 89.320 in accordance with an FAA-accepted means of compliance; and

(b) All of the following conditions are met:

(1) Inspection requirements for production of remote identification broadcast modules. A person responsible for the production of remote identification broadcast modules must, upon request, allow the Administrator to inspect the person's facilities, technical data, and any remote identification broadcast modules the person produces, and to witness any tests necessary to determine compliance with this subpart.

(2) Audit requirements. A person responsible for the production of remote identification broadcast modules must cause independent audits to be performed on a recurring basis, and additionally whenever the FAA provides notice of noncompliance or potential noncompliance, to demonstrate the remote identification broadcast modules listed under a declaration of compliance meet the requirements of this subpart. The person responsible for the production of remote identification broadcast modules must provide the results of all such audits to the FAA upon request.

(3) Product support and notification. A person responsible for the production of remote identification broadcast modules must maintain product support and notification procedures to notify the public and the FAA of any defect or condition that causes the remote identification broadcast module to no longer meet the requirements of this subpart, within 15 calendar days of the date the person becomes aware of the defect or condition.

(4) Instructions. A person responsible for the production of a remote identification broadcast module must make available instructions for installing and operating the remote identification broadcast module to any person operating an unmanned aircraft with the remote identification broadcast module.

[Amdt. No. 89-1, 86 FR 4505, Jan. 15, 2021; 86 FR 13630, Mar. 10, 2021]
 

§ 89.525 Labeling.

(a) No person may produce a standard remote identification unmanned aircraft under § 89.515 unless it displays a label indicating that the unmanned aircraft meets the requirements of this part. The label must be in English and be legible, prominent, and permanently affixed to the unmanned aircraft.

(b) No person may produce a remote identification broadcast module under § 89.520 unless it displays a label indicating that the equipment meets the requirements of this part. The label must be in English and be legible, prominent, and permanently affixed to the broadcast module.

 

§ 89.530 Submission of a declaration of compliance for FAA acceptance.

(a) Eligibility. A person responsible for the production of a standard remote identification unmanned aircraft under § 89.515 or a remote identification broadcast module under § 89.520 must submit a declaration of compliance for acceptance by the FAA.

(b) Required information for standard remote identification unmanned aircraft. The person responsible for the production of a standard remote identification unmanned aircraft requesting acceptance of a declaration of compliance must declare that the unmanned aircraft complies with the requirements of this subpart by submitting a declaration of compliance to the FAA in a form and manner acceptable to the Administrator. The declaration must include at a minimum the following information:

(1) The name, physical address, telephone number, and email address of the person responsible for production of the unmanned aircraft.

(2) The unmanned aircraft's make and model.

(3) The unmanned aircraft's serial number, or the range of serial numbers for which the person responsible for production is declaring compliance.

(4) The FCC Identifier of the 47 CFR part 15-compliant radio frequency equipment used and integrated into the unmanned aircraft.

(5) The means of compliance used in the design and production of the unmanned aircraft.

(6) Whether the declaration of compliance is an initial declaration or an amended declaration, and if the declaration of compliance is an amended declaration, the reason for the amendment.

(7) A declaration that the person responsible for the production of the unmanned aircraft:

(i) Can demonstrate that the unmanned aircraft was designed and produced to meet the minimum performance requirements of § 89.310 by using an FAA-accepted means of compliance.

(ii) Complies with the requirements of § 89.515(b).

(8) A statement that 47 CFR part 15-compliant radio frequency equipment is used and is integrated into the unmanned aircraft without modification to its authorized radio frequency parameters.

(c) Required information for remote identification broadcast modules. The person responsible for the production of a remote identification broadcast module under § 89.520 that is requesting acceptance of a declaration of compliance must declare that the remote identification broadcast module complies with the requirements of this subpart by submitting a declaration of compliance to the FAA in a form and manner acceptable to the Administrator. The declaration must include at a minimum the following information:

(1) The name, physical address, telephone number, and email address of the person responsible for production of the remote identification broadcast module.

(2) The remote identification broadcast module's make and model.

(3) The remote identification broadcast module's serial number, or the range of serial numbers for which the person responsible for production is declaring compliance.

(4) The FCC Identifier of the 47 CFR part 15-compliant radio frequency equipment used and integrated into the remote identification broadcast module.

(5) The means of compliance used in the design and production of the remote identification broadcast module.

(6) Whether the declaration of compliance is an initial declaration or an amended declaration, and if the declaration of compliance is an amended declaration, the reason for the amendment.

(7) A declaration that the person responsible for the production of the remote identification broadcast module:

(i) Can demonstrate that the remote identification broadcast module was designed and produced to meet the minimum performance requirements of § 89.320 by using an FAA-accepted means of compliance.

(ii) Complies with the requirements of § 89.520(b).

(8) A statement that 47 CFR part 15-compliant radio frequency equipment is used and is integrated into the remote identification broadcast module without modification to its authorized radio frequency parameters, and a statement that instructions have been provided for installation of 47 CFR part 15-compliant remote identification broadcast module without modification to the broadcast module's authorized radio frequency parameters.

 

§ 89.535 Acceptance of a declaration of compliance.

(a) The Administrator will evaluate a declaration of compliance that is submitted to the FAA and may request additional information or documentation, as needed, to supplement the declaration of compliance.

(b) If the Administrator determines that the submitter has demonstrated compliance with the requirements of this subpart, the FAA will notify the submitter that the Administrator has accepted the declaration of compliance.

 

§ 89.540 Rescission and reconsideration.

(a) Rescission of the FAA's acceptance of a declaration of compliance.

(1) A declaration of compliance is subject to ongoing review by the Administrator. The Administrator may rescind acceptance of a declaration of compliance under circumstances including but not limited to the following:

(i) A standard remote identification unmanned aircraft or remote identification broadcast module listed under an accepted declaration of compliance does not meet the minimum performance requirements of § 89.310 or § 89.320.

(ii) A previously FAA-accepted declaration of compliance does not meet a requirement of this subpart; or

(iii) The FAA rescinds acceptance of the means of compliance listed in an FAA-accepted declaration of compliance.

(2) The Administrator will notify the person who submitted the FAA-accepted declaration of compliance of any issue of noncompliance.

(3) If the Administrator determines that it is in the public interest, prior to rescinding acceptance of a declaration of compliance, the Administrator may provide a reasonable period of time for the person who submitted the declaration of compliance to remediate the noncompliance. A failure to remediate the noncompliance constitutes cause for rescission of the FAA's acceptance of the declaration of compliance.

(4) The Administrator will notify the person who submitted the declaration of compliance of the decision to rescind acceptance of the declaration of compliance by publishing a notice of rescission in the Federal Register.

(b) Petition to reconsider the FAA's decision to rescind acceptance of a declaration of compliance.

(1) The person who submitted the FAA-accepted declaration of compliance or any person adversely affected by the rescission of the Administrator's acceptance of a declaration of compliance may petition for a reconsideration of the decision by submitting a request to the FAA in a form and manner acceptable to the Administrator within 60 calendar days of the date of publication in the Federal Register of notification of rescission.

(2) A petition to reconsider the rescission of the Administrator's acceptance of a declaration of compliance must show that the petitioner is an interested party and has been adversely affected by the decision of the FAA. The petition must also demonstrate at least one of the following:

(i) The petitioner adduces a significant additional fact not previously presented to the FAA.

(ii) The Administrator made a material error of fact in the decision to rescind acceptance of the declaration of compliance.

(iii) The Administrator did not correctly interpret a law, regulation, or precedent.

(3) Upon consideration of the information submitted by the petitioner, the Administrator will notify the petitioner and the person who submitted the declaration of compliance (if different) of the decision on whether to reinstate the Administrator's acceptance of the declaration of compliance.

(c) Inapplicability of part 13, subpart D, of this chapter. Part 13, subpart D, of this chapter does not apply to the procedures of paragraphs (a) and (b) of this section.

 

§ 89.545 Record retention.

A person who submits a declaration of compliance under this subpart that is accepted by the Administrator must retain the following information for as long as the standard remote identification unmanned aircraft or remote identification broadcast module listed on that declaration of compliance is produced plus an additional 24 calendar months, and must make available for inspection by the Administrator the following:

(a) The means of compliance, all documentation, and substantiating data related to the means of compliance used.

(b) Records of all test results.

(c) Any other information necessary to demonstrate compliance with the means of compliance so that the standard remote identification unmanned aircraft or remote identification broadcast module meets the remote identification requirements and the design and production requirements of this part.